Skip to content
Find my rebates
Heat Pumps

Questions to Ask a Heat Pump Installer at the Home Visit

By · Updated October 27, 2026

Quick answer

Use the home visit to judge the installer. Check the license and insurance first, watch whether they measure your home, ask how they'll size the system and test ducts, refrigerant and airflow, and get the paperwork. Walk away from pressure, cash-only deals or a size quoted without measuring.

The home visit tells you more about an installer than the quote does. A careful installer spends real time measuring your home, asks you questions, and explains how they’ll size the system. ENERGY STAR says a contractor “should spend significant time inspecting your current system and home to assess your needs.” Below are the questions to ask a heat pump installer, grouped by stage, plus the answers that should make you look elsewhere. For the basics first, see our complete heat pump guide.

Five stages of questions to ask a heat pump installer: before the visit, during the visit, sizing, the installation, and after the install

Before the visit: check the installer

A few minutes of checking can save you a bad hire.

  • License and insurance. The FTC advises you to “consider only contractors who are licensed and insured.” Check the license with your state or county, and ask for proof of insurance. Rules differ by state, so look up yours.
  • References. ENERGY STAR suggests asking for customer references and calling them. Ask whether the job finished on time and on budget.
  • Your notes. Write down your current system’s age, any rooms that are too hot or cold, and big electric loads you plan to add, such as an EV charger.
Checklist before a heat pump installer visits: check the license with your state or county, ask for proof of insurance, call references, and note your system age, problem rooms and planned loads

During the visit: what a good installer looks at

Watch what they do, not just what they say. A thorough visit usually includes:

  • measuring rooms and windows, and asking about insulation in the attic, walls and basement,
  • looking at your current system and ducts (if you have them),
  • checking where the outdoor unit could go,
  • looking at your electrical panel.

A heat pump buying guide on NEEP’s website says a whole-home proposal “should always start with a load calculation,” built from room and window measurements and insulation levels. An installer who glances around for ten minutes and quotes a size can’t have done that.

What a good heat pump installer looks at during a home visit: rooms and windows, insulation, the current system and ducts, the outdoor unit location, and the electrical panel

Questions to ask a heat pump installer about sizing

  1. How will you size the system? ENERGY STAR says the contractor should use the actual characteristics of your home, not a rule of thumb.
  2. Will you do a Manual J load calculation, and can I have a copy? It’s the room-by-room calculation that sets the size. Our guide on what size heat pump you need explains it.
  3. Is this model rated for our winter temperatures? Ask how it performs on the coldest days where you live.
  4. What backup heat do you plan, and when will it turn on? Our guide to aux heat vs emergency heat explains what backup heat does.

For a rough number before the visit, try our heat pump sizing calculator. The installer’s load calculation is the one that counts.

Questions about the installation

The NEEP-hosted guide and ENERGY STAR’s quality installation advice point to these:

  1. Where will the outdoor unit go, and how will it be mounted? Ask about snow, roof runoff and noise near bedrooms.
  2. Where will the indoor units or vents go, and why? For ductless systems, ask where the line sets will run on the outside of the house.
  3. Will you test my ducts for leaks and fix them? ENERGY STAR’s quality installation page says to ask for a duct leakage test and needed repairs.
  4. Will you test and adjust the refrigerant charge and airflow? ENERGY STAR says the charge should be tested and adjusted, and airflow should meet the manufacturer’s specifications.
  5. Do I need my own electrician, or a panel or service upgrade? Get the answer in writing.
  6. Will you use subcontractors? Who are they, and what will they do?

Questions about after the install

  1. Will you show me how to run and maintain the system? That includes how to change the filter.
  2. Will you leave me the paperwork? The ENERGY STAR bid checklist asks for the manuals, the Manual J calculation, the AHRI certificate and records of any tests.
  3. What warranty do you give on your work, and for how long?
  4. Which rebates fit this system, and will you help with the paperwork? Many programs need approval before work starts. Our heat pump rebates guide shows what’s available by state.
Paperwork to ask a heat pump installer for: the Manual J load calculation, the AHRI certificate, test records for duct leakage, charge and airflow, and the manuals

What a good installer asks you

The questions should go both ways. Expect a careful installer to ask:

  • which rooms are uncomfortable now, and when,
  • whether you want to keep your current furnace or boiler as backup,
  • whether you plan other electric upgrades soon,
  • what your recent energy bills look like.

An installer who asks nothing about your home is guessing.

Answers that should end the conversation

  • “Heat pumps don’t really work in cold climates” or “every heat pump needs a backup system.” The NEEP-hosted guide says to find someone else if you hear these.
  • A size quoted without measuring. ENERGY STAR warns against rule-of-thumb sizing.
  • Pressure to sign today. The FTC lists pressure for an immediate decision as a sign of a scam.
  • Full payment up front, or cash only. The FTC says don’t pay the full amount up front.
  • No written proposal. Get every promise in a signed, written contract that includes the contractor’s license number and estimated start and finish dates.
Six heat pump installer red flags: saying heat pumps don't work in cold climates, saying every heat pump needs backup, a size quoted without measuring, pressure to sign today, full payment up front or cash only, and no written contract

After the visits

Once you have 2 or 3 written quotes, put them side by side. Our guide on how to compare heat pump quotes has a worksheet and the follow-up questions to send. Your notes from these visits will tell you which installers took the job seriously.

Plan with your numbers

Heat Pump Cost Calculator

Build an installed-cost budget from equipment, labor and extras.

Open tool

Sources & references

Sam Carter, editor of ElectrifyTips

About the author

Editor, ElectrifyTips

Sam Carter is the editor of ElectrifyTips, based in California. He turns official sources, such as the US Department of Energy, ENERGY STAR, EIA and state rebate programs, into plain-English guides and free calculators for US homeowners. He is not a licensed contractor or tax advisor, so every guide links to its sources.

More about Sam